When measuring the height of a motorhome to pick out a cover for it the key is to measure from the bottom of the body to the top not including the ladder or any roof top accessories. If you check out the picture I attached you'll see what I mean. I looked up your 1995 Winnebago Itasca Passage and it measures 11 feet from the ground to the top of the AC unit so a cover like the part # 290-64823 will fit the body of the motorhome well it's height is 9.5 feet basically. view full answer...
It sounds like the Buyers Products Rocker Switch # 3373014187 will work very well for a replacement switch in your 1995 Southwind RV. this is a 3 pin momentary open/close switch that features overall dimensions of 2" tall/long, 1" wide, and about 2" deep (I have attached a diagram to assist).
It has a continuous current rating of 10 amps and is made right here in the USA. view full answer...
As long as the RV sewer hoses are 3 inch in diameter without a bayonet fitting like Camco part # CAM39611 the hoses will slide over each end of the coupler part # CAM39203 to join them together. You do not need to heat the coupler up to seal the connection. view full answer...
The most common upgrades we see on motorhomes is rear anti-sway bar, sumo springs front/rear, and steering stabilizer in that order. These are the most worthwhile upgrades and the ones you will notice an improvement from most. I have attached the correct options below.
Roadmaster Rear Anti-Sway Bar part # RM-1139-146
SumoSprings Rebel Custom Helper Springs part # SSF-170-40-2 (Front) and part # SSR-184-40-1 (Rear)
Roadmaster Reflex Steering Stabilizer part # RM-RBK22-RSSA view full answer...
Powered RV steps that still operate but that make bad mechanical noises may not need a new motor, but you're right that it is likely you'll need a new gearbox and/or linkage. There are two possible kits for your step unit.
Part # LC379161 is the B style linkage for the Kwikee Step Series 28, 31, 37 and 39. This is Kwikee part number 1101426.
Part # LC379162 is the C style linkage for the Series 26 step, Kwikee part 1101427.
My contact at Lippert/Kwikee said that on the bottom of your... view full answer...
Your model number of 7333C886 means you have a Coleman Mach and the correct replacement shroud is the MaxxAir part # MA00-325001 which you referenced. view full answer...
I would be happy to go over how to install the Tekonsha Prodigy P2 # 90885 you were looking at in your 2001 Winnebago Brave Motorhome built on the Workhorse Chassis, but there is not a plug and play option available for the Workhorse Chassis.
Instead you will need to use the Wiring Kit # 5506 and like some extra wire # 10-2-1 due to the length of your RV to get the controller installed.
You will need to make the following connections to the controller wiring harness:
Red wire to cold... view full answer...
The only entry door latches we offer are the Global Link RV Entry Door Locking Latch Kits which are available in chrome part # 295-000002, white part # 295-000021, and black part # 295-000019. These door latches will all install in a cutout from 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall. Therefore, in order to make either option work you may need to modify your cutout to accommodate this range but we do not offer any other options. That said, I really do not think you will be able... view full answer...
Before replacing the linkage, like part # LC379648, on your steps first check the gear. I spoke with my contact at Lippert who said that when the motor is continually running that means that there are teeth missing on the gear. If you have a single or double step unit then the replacement gear is part # LC301696. view full answer...
The Adco Olefin HD RV Cover for Class A Motorhomes Up to 34' Long part # AD64ZR is the best and most durable cover option for a Winnebago Brave 34D Motorhome. This is partly due to the olefin top panel which does a better job of protecting from uv rays and water than the three layer panel of its competitors. It also has more extras like ladder cap and rain gutter covers as well as a better warranty than the Camco UltraGuard part # CAM45733. view full answer...
Most likely yes, etrailer Landing Gear Set # RVLG-8000 will fit your 1994 Avion Fleetwood 5th wheel trailer. You will want to measure the distance between the bracket stops on the sides of the outer tubes of your existing landing gear to make sure it is a match. I have included a picture showing these measurements.
The 15-1/2 inches is the distance between the upper and lower stops. The 17-1/2 measure is the distance from the top of the upper stop to the bottom of the lower stop. I have... view full answer...
The Gustafson RV Vanity Light part # 277-000325 can be used with ether incandescent bulbs or LEDs. It does not come with bulbs so if you want to use LEDs then just order the LED Light Bulbs part # DI68VR. view full answer...
I do have an option for you but there aren't any brake controller wiring provisions on the Workhorse chassis. That said, all you will have to do is run some wires from the trailer connector to the the controller and then from the controller to the battery using the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers part # 5506. This will be almost everything you need to install an electric trailer brake controller like the Tekonsha Prodigy P3 Trailer Brake Controller... view full answer...
If you're just wanting to replace the rooftop unit and keep the rest of the equipment that you currently have then you'll just want to see how it connects to the controller. It can have a 6-pin connector, 9pin connector, or be hardwired in. If you have 6-pin connector then you can go with the Furrion # FR26PR. For a 9-pin connector you'll need part # FR82PV to get a wire harness adapter. If the unit is hardwired you'll need to reach out to Furrion and the manufacturer of the current AC... view full answer...
On your 2015 Winnebago Brave I recommend starting with the Roadmaster Rear Anti-Sway Bar part # RM-1139-145 this will help a great deal by adding an additional heavier sway bar to combat the side to side movement that is incredibly common when driving a motorhome. There is a notable difference in the ride after installation.
The second thing I always recommend is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes part # RM-RBK22-RSSA this will eliminate... view full answer...
The best option we have for you is to use the Valterra Check Valve part # P23415LFVP and then go to a local hardware store to look for a 1/2" to 5/8" adapter as we do not carry a check valve with both 1/2" MPT and 5/8" MPT fittings. These are pretty common through so I don't think you will have any issue finding one. In order to join the fittings together you will also want to use the Valterra PTFE Thread Seal Tape part # A05-0265. view full answer...
Hey Tim,
I'll need to know more about your chassis in order to see if there's a compatible air spring available. Could you send me the model number and possibly the VIN so I can see if I can get some more info on it? view full answer...
The 3 wires on the back of the Atwood RV Water Heater # AT96163 you referenced should be attached accordingly:
Black - Hot Lead to Switch
Green - Ground Lead to Ground
White - Common Lead to Element
I have attached a clip from the instructions for you to check out. Please note that we recommend that the installation and service must be performed by a qualified installer, service agency, or gas supplier. view full answer...
The Gustafson 12V RV Vanity Light w/ Shades # 277-000324 is just held in place with a few screws so you can mount it any direction you want. view full answer...
Yes, you can use the electric heat strip for with an Advent AC unit:
**Electric Heat Strip for Advent Air RV Air Conditioners - 5,500 BTU # ACMHD.
*Advent Air RV Air Conditioner - 13,500 Btu - White # ACM135.
These two units are made for each other. view full answer...
Go To Results